#Renogy battery monitor bluetooth update#
#Renogy battery monitor bluetooth manual#
#Renogy battery monitor bluetooth Bluetooth#

4 Incomplete tech specs, poor monitoring tool.Please avoid too high a voltage difference between paralleled batteries, despite the auto-balancing function, to avoid triggering the over-current protection.It is made ONLY for 12V parallel connections using the batteries of the same manufacturer and model. Failure to make a secure connection could result in overheating and battery damage. Make sure to tighten the battery terminals securely and use appropriate size wiring.When the battery voltage drops to 0V, please reactivate the battery using an external charging device that has the lithium battery activation function.

If you have any questions regarding this product, please contact When connecting the batteries in parallel, a communication cable is not needed to enable the auto-balancing function.

#Renogy battery monitor bluetooth Bluetooth#

Please kindly note that the new Renogy BT-2 bluetooth module with RJ45/RS485 port is compatible with this smart Li battery. The Renogy Adventurer Li and Rover charge controller are fully compatible with this battery. If you’re searching for a deep cycle battery for caravan, cabin, or marine use, then this lightweight, auto-balanced, ultra-safe, long-cycle-life lithium-ion battery is the perfect plug-and-play solution for you! The state-of-the-art battery cells ensure a long cycle life and exceptional discharge performance. The integrated smart battery management system (BMS) not only protects this 12V 100Ah LiFePO4 battery from various abnormal conditions but monitors and manages the charging/discharging process. 13.4v to 13.6v, in an effort to keep the LiFePO4 battery at 100% SOC at rest when the sun is shining (100% SOC for a 12v 100AH BB battery at rest is 13.6v according to BB).The Renogy Smart Lithium Iron Phosphate Battery enables auto-balance among parallel-connections and provides more flexibility for battery connection. Ready for another night without the sun.Ĭhanged settings - 5 Float Charge (v) from 13.6v to 13.8v - 6 Boost Char Return Volt. Today the solar controller with one solar panel attached recharged the battery to 100% SOC (boost voltage 14.4v), then went to 13.8v float charge, resulting in 0 amps going into battery (its already at 100% SOC) and all other small dc loads were supplied by the solar controller at 13.8v. The inverter introduces another 2-2.5A parasitic load on the 12v system if left on when not in use. So if I turn the inverter off when not in use at night, the 12v system only loose about 12 amp hours a night parked. There is about a 1 amp parasitic load on the 12v dc system in the camper, heater/ac thermostat, three way fridge eyebrow controller, smoke detector, propane detector. The BT-2 connected the DCC50S with the iPhone, no problems. I do believe that some of the settings are not required for a battery charger/solar controller with no LOAD hookup.Īnother day with sunshine. I do have some reasons for some of the settings. You might want to choose other set points. I have three 12v 100AH LiFePO2 batteries in parallel, the DCC50S, and a charger/inverter MSH1230 M.Each of the three batteries have their own BMS internal to the battery case.

#Renogy battery monitor bluetooth manual#

No surprise here as the DCC50S manual is also very poorly written and the devices connected to the DCC50S are not consistently named in the manual.ĭoes anyone want to take a shot at defining any of these settings described above ? Their min/max values and interaction with other settings are not defined in the owners manual. These settings are not defined anywhere in the owners manual.

(many of the setting descriptions are truncated) If you select Battery Type 'USER', the battery type indicator light turns white. There are several settings you can change in the Renogy BT app. I do not know why it would not connect right up earlier.

I got it to connect to the phone with Bluetooth so there is hope. Viewed record and other screens, then came back too settings screen to find that most of the settings I saved were still there (found that the EQ min time had changed from 0 to 10).

#Renogy battery monitor bluetooth update#

I was able to read data from the DCC50S, view the device battery 'USER' type settings with the Read button, update a few settings, use the Save button to save the setting changes. It connected to the BT-2 Bluetooth device. Then reversed the process, turned on service battery + circuit switch, turned on the solar panel + circuit switch and plugged in the BT-2 cable to the DCC50S RJ45 port. Then I tried unplugging the BT-2 cable from the DCC50S RJ45 port, turned off the solar panel input (even though it was dark outside), Opened the 12v dc + switch to the DCC50S service battery + port. After trying everything I could think of, with no Bluetooth connected state on Renogy-BT app, I was about to give up.